hand crimp tool for 2.00mm (.079") pitch micro blad e board-in crimp terminals doc no: ats-638234900 release date: 04-09-10 uncontrolled copy page 1 of 8 revision: a revision date: 04-09-10 hand crimp tool specification sheet order no. 63823-4900 features a full cycle ratcheting hand tool ensures complete crimps ergonomic soft grip handles for comfortable crimpin g a precision user-friendly terminal locator wire sto p holds terminals in the proper crimping position right and left handed applications this tool is whma-ipca620 class 2 compliant as indi cated this tool is rohs compliant, however rohs compliant is not required scope products : 2.00mm (.079") pitch micro blade board -in crimp te rminal 26-30 awg. terminal order no. wire size insulation diameter st rip length terminal series no. loose piece reel awg mm2 mm in. mm in. 50034 50034-8100 50034-8000 26-30 0.12-0.05 0.80-1.40 .031-.055 1.40-1.90 .055-.075 customer to cut off terminal from reel: 0,.2mm (.0 08) maximum cut-off tab. definition of terms the above terminal drawing is a generic terminal re presentation. it is not an image of a terminal lis ted in the scope. insulation crimp brush strip length bell mouth crimp height bend down bend up rolling conductor crimp twisting type 4d
hand crimp tool for 2.00mm (.079") pitch micro blad e board-in crimp terminals doc no: ats-638234900 release date: 04-09-10 uncontrolled copy page 2 of 8 revision: a revision date: 04-09-10 conditions: after crimping, the conductor profiles should measu re the following. conductor crimp wire size height (ref.) width (ref.) profile terminal series no awg mm 2 mm in. mm in. 26 28 30 26 0.12 0.57-0.62 .022-.024 1.05 .041 x 28 0.08 0.56-0.61 .022-.024 1.05 .041 x 50034 30 0.05 0.53-0.58 .021-.023 1.05 .041 x insulation crimp wire size max height (ref.) width (ref.) pull force minimum terminal series no awg mm 2 mm in. mm in. n lb. 26 0.12 1.15 .045 1.41 .056 19.6 4.4 28 0.08 1.15 .045 1.41 .056 9.8 2.2 50034 30 0.05 1.10 .043 1.41 .056 4.9 1.1 operation caution: install only molex terminals listed above with this tool. do not crimp hardened objects as damage can occur to the tool or die. open the tool by squeezing the handles together. a t the end of the closing stroke, the ratchet mechan ism will release the handles and the hand tool will spring o pen. see figure 1. crimping terminals 1. select the desired terminal listed from the preceding charts. then install it in the proper locator (see chart above and see locator installation on page 5). 2. make sure the center of the locator is in the down position. with the locator attached, push the locator button on the back of the hand tool to bring the locator forward through the tooling. see figure 2. squeeze handles together handle will spring open figure 1 locator in down postion push on the locator button figure 2
hand crimp tool for 2.00mm (.079") pitch micro blad e board-in crimp terminals doc no: ats-638234900 release date: 04-09-10 uncontrolled copy page 3 of 8 revision: a revision date: 04-09-10 release locator button terminal figure 3 locator pushed thru tooling terminal locator button pushed in locator figure 5 terminal wire against the wire stop wire wire stop is part of the locator pre-stripped wire terminal 3. while holding in the locator button, load the termi nal into the proper nest opening in the locator, based on the wire gaug e or terminal type markings on the hand tooling. see figure 3. 4. release the locator button, allowing the locator to return to the crimping position. 5. close the tool handle until the first ratchet posit ion engages. see figure 4. 6. insert the properly stripped wire through the termi nal and against the wire stop. see figure 5. 7. crimp the terminal by squeezing the tool handles un til the ratchet mechanism cycle has bee n completed. release the h andles to open the jaws. note: the tamper proof ratchet action will not rele ase the tool until it has been fully closed. 8. remove the crimped terminal from the terminal locat or by pulling on the wire. 9. visually inspect the crimped terminal for proper cr imp location. 10. on some large o.d. wires, it may not be possible to insert the wire with the tool partially closed. t hose wires should be inserted with the hand tool in the open p osition. insert the wire above the terminal in the punch and against the wire stop then close the tool. see fig ure 6. partially close handle tooling partially closed figure 4 first ratchet position open position
hand crimp tool for 2.00mm (.079") pitch micro blad e board-in crimp terminals doc no: ats-638234900 release date: 04-09-10 uncontrolled copy page 4 of 8 revision: a revision date: 04-09-10 note: a crimp height chart is provided with this manual a s reference only. due to the wide range of wires, strands, insulation diameters, and durometers available, actual crimp height measurements may very slightly. an occasional, destructive, pull fo rce test should be preformed to check hand tool crimp. pull force value must exceed the minimum pull force specifications listed. locator replacement see the parts list on the last page of this documen t for the proper locator order number. follow the steps below to replace the locator. 1. open the crimp hand tool. 2. squeeze gently on the lower area shown in figure 7a with your thumb and index finger. the lower tabs of the locator should disengage from the hand tool. 3. lift and pull away from the hand tool. the top loc ator hooks should slip out of the top slots easily. see figure 7a. 4. to reinstall the new locator, make sure the hand to ol is in the open position. 5. press the red insert down as far as it will go as s hown in figure 7b. 6. holding onto the lower part of the locator with you r thumb and index finger, insert the locator top ho oks (2) into the hand tool top slots. 7. rotate the locator down and press the lower tabs in to the two bottom slots of the hand tool. to secur e the locator into place, the lower tabs must snap into p lace on the hand tool frame. terminal figure 6 wire wire stop squeeze here squeeze here locator figure 7a top hooks top slots of handtool lower tabs make sure center of locator is in the down position figure 7b figure 8 push on handle jaws open pull open tooling tooling m3 bhcs
hand crimp tool for 2.00mm (.079") pitch micro blad e board-in crimp terminals doc no: ats-638234900 release date: 04-09-10 uncontrolled copy page 5 of 8 revision: a revision date: 04-09-10 figure 12 squeeze the link in the handle hold the hand tool in position setting wheel ratchet release lever right or left hand operation this hand tool has an added feature that can be con verted from a right handed application to a left handed ap plication. it is necessary to reverse the tooling along with t he locator if using the left handed application. follow the step s below: 1. the locator must be removed before reversing the tooling. 2. remove the m3 bhcs which is holding the upper tooling. 3. flip the upper tooling to the opposite side and replace the m3 bhcs make sure the small markings on the front and back of the hand tool frame match up and are on the outside of the hand tool frame. see figure 8 and 9. 4. do the same thing with the lower tooling and tighten the m3 screws. be sure the small markings line up. 5. reinstall the locator by following the instructions in the locator replacement section. maintenance it is recommended that each operator of the tool be made aware of, and responsible for, the following maintenance steps: 1. remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth. 2. do not use any abrasive materials that could damage the tool. 3. make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine oil. do not oil excessively. the tool was engineered for durability but like any other equipm ent it needs cleaning and lubrication for a maximum service life of trouble free crimping. light oil (such as 30 weight automotive oil) used at the oil points, e very 5,000 crimps or 3 months, will significantly enhance the tool life. ratchet release lever figure 11 lubrication points (both sides) light oil (every 3 months or 5,000 crimps) figure 10 match up marks front back figure 9
hand crimp tool for 2.00mm (.079") pitch micro blad e board-in crimp terminals doc no: ats-638234900 release date: 04-09-10 uncontrolled copy page 6 of 8 revision: a revision date: 04-09-10 4. wipe excess oil from hand tool, particularly from c rimping area. oil transferred from the crimping ar ea onto certain terminations may affect the electrical char acteristics of an application. 5. when tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimpi ng dies, and store the tool in a clean, dry area. miscrimps or jams should this tool ever become stuck or jammed in a p artially closed position, do not force the handles open or closed. the tool will open easily by pressing up on the rat chet release lever in the movable handle. see figu re 11 how to adjust tool preload (see figure 12) this hand tool is factory preset to 25-45 lbs. prel oad. it may be necessary over the life of the tool to adjust tool handle preload force. listed below are the steps r equired to adjust the crimping force of the hand to ol to obtain proper crimp conditions: 1. hold the hand tool in the palm of your hand as show n in figure 12. using the index finger squeeze the link towards the top of the hand tool frame. this will release the preload adjustment wheel. 2. rotate the setting wheel counter-clockwise (ccw) to increase handle force. the numbers will display h igher. to decrease handle force, rotate the setting wheel clockwise (cw). 3. release the link to lock the setting wheel in place . 4. check the crimp specifications or conduct a pull te st after tool handle preload force is adjusted. warranty this tool is for electrical terminal crimping purpo ses only. this tool is made of the best quality ma terials. all vital components are long life tested. all tools are war ranted to be free of manufacturing defects for a pe riod of 30 days. should such a defect occur, we will repair o r exchange the tool free of charge. this repair or exchange will not be applicable to altered, misused, or damaged t ools. this tool is designed for hand use only. an y clamping, fixturing, or use of handle extensions voids this w arranty. caution : molex crimp specifications are valid only when u sed with molex terminals and tooling. cautions: 1. manually powered hand tools are intended for low vo lume or field repair. this tool is not intended for production use. repetitive use of this tool should be avoided. 2. insulated rubber handles are not protection against electrical shock. 3. wear eye protection at all times. 4. use only the molex terminals specified for crimping with this tool.
hand crimp tool for 2.00mm (.079") pitch micro blad e board-in crimp terminals doc no: ats-638234900 release date: 04-09-10 uncontrolled copy page 7 of 8 revision: a revision date: 04-09-10 certification molex does not certify or re-certify hand tools but rather supplies the following guidelines for custo mers to re-certify hand tools. % this tool is qualified to pull force only. to re-c ertify, crimp a terminal to a wire, which has been stripped 12.7mm (1/2) long, so there is no crimping of the insulation. pull the terminal and wire at a rate n o faster than 25mm (1.00) per minute. see the molex web site fo r the quality crimp handbook for more information o n pull testing. % if the tool does not meet minimum pull force values , handle preload should be increased and the pull t est rerun, (see how to adjust preload). % when the hand tool is no longer capable of achievin g minimum pull force, it should be taken out of ser vice and replaced.
hand crimp tool for 2.00mm (.079") pitch micro blad e board-in crimp terminals doc no: ats-638234900 release date: 04-09-10 uncontrolled copy page 8 of 8 revision: a revision date: 04-09-10 ratchet release lever 2 figure 13 1 3 parts list item number order number description quantity ref 63823-4900 hand crimp tool figure 13 1 63823-4975 locator assembly (red) 1 2 63810-0104 spring, return 1 3 63810-0105 spring, ratchet 1 americas headquarters lisle, illinois 60532 u.s.a. 1-800-78molex amerinfo@molex.com far east north headquarters yamato, kanagawa, japan 81-462-65-2324 feninfo@molex.com far east south headquarters jurong, singapore 65-6-268-6868 fesinfo@molex.com european headquarters munich, germany 49-89-413092-0 eurinfo@molex.com corporate headquarters 2222 wellington ct. lisle, il 60532 u.s.a. 630-969-4550 fax: 630-969-1352 visit our web site at http://www.molex.com
|
